Posted in

How to remove a submersible pump from a well?

Hey everyone, it’s Jake here from your go-to submersible pump supplier—you know, the guys who show up when your well’s sputtering and you don’t wanna deal with a random handyman who breaks more than they fix. Today I’m talking about something I get asked all the time, especially when we sell a pump and folks run into issues: how to actually yank that submersible pump outta the well without messing everything up. I’ve seen too many folks rush this, yank the cable wrong, or scratch the pump so bad it dies before it even gets a new home, so let’s keep this real, no fancy jargon, just what works. Submersible Pump

First off, let’s get one thing straight: submersible pumps are built to be under water, not out in the open. They’re attached to that long electrical cable and a discharge pipe, and if you don’t handle ’em right, you could end up with a tangled mess, a broken pipe, or worse—getting stuck halfway in the well and having to call us to fish it out (we do that, but y’all don’t wanna pay for that emergency call, trust me). I’ve been doing this for 8 years, and I still see a lot of DIYers skip the prep work, so let’s start with the basics you can’t ignore.

Before you even touch the well cap, you gotta prep. First, shut off the power—like, the main breaker for your well pump. Don’t just flip the switch on the pressure tank, I’ve seen that shock someone when they accidentally tug the cable. Dead serious, if you skip this step, you’re playing with fire (or electricity, whatever’s worse in this scenario). Next, grab your tools: a pipe wrench (not a regular adjustable one, those slip), a pair of heavy-duty work gloves (those thin garden ones? No way, you’ll slice your hands on pipe edges), a level (wait, yeah, a small level, we’ll get to that), and a buddy. Don’t do this alone. Why? Because that pump can weigh 50 to 100 pounds when it’s dry, and if it’s stuck on the pipe, you’re gonna need an extra pair of hands to keep things steady. Pro tip from our team: keep a roll of Teflon tape and some extra cable ties nearby too, you’ll see why.

Now, get to the well. Most wells have a cap—some are metal, some are plastic—pop that off carefully, don’t drop it down the hole (we’ve had to fish those out too, not fun). Once the cap’s off, you’ll see the discharge pipe (that’s the fat PVC or metal pipe going down) and the electrical cable running along it, taped or clamped on. Here’s the first big mistake: yanking the cable first. No way. The cable is only meant for power, not pulling the pump. That’s how you snap the cable mid-pull and have to fish it out. Instead, you wanna loosen the coupling that connects the discharge pipe to the next section. Use that pipe wrench—grip it tight, turn counterclockwise. Don’t force it if it’s stuck; spray a little WD-40 on it and wait 10 minutes, that stuff works miracles on old, rusted couplings.

Once the coupling is loose, you’ve got two things holding the pump in: the pipe and the cable. Now, start pulling slow. Grab the pump’s lifting eye (that’s the little metal ring on top—if you don’t see one, that’s a red flag, maybe you’ve got the wrong pump, come talk to us). One of you holds the pipe steady so it doesn’t twist, the other pulls the lifting eye up steadily, about 6 inches at a time. Every few feet, stop and check the cable: make sure it’s still securely attached to the pipe, no kinks, no frays. Kinks in the cable? Those can break the wires inside, so if you see a kink, straighten it gently, don’t yank it hard.

Wait, what if the pump gets stuck halfway? Don’t panic. A lot of times, that’s because the well casing has some build-up (minerals, dirt) or the pump’s intake got clogged with sediment. Here’s where that level comes in: hold it against the pipe. If it’s leaning one way, that means the pump’s hitting the side of the casing. Straighten it out a little, then pull again, slow. If that doesn’t work, don’t keep yanking—that’s how you break the pipe. Call us, or a well technician, but don’t make it worse. We’ve seen pipes snap right in half because someone forced a stuck pump, and replacing that pipe is way more expensive than just waiting it out.

Once you get the pump out, set it on a sturdy workbench or sawhorses—don’t set it on the ground, you’ll get dirt in the intake and mess up the impeller. Now, let’s talk about what to do with it once it’s out, because a lot of folks wanna test it before they install the new one. If you’re testing, make sure you only submerge the pump’s intake (the bottom part) in clean water—don’t plug it into power to test it out of water, that’ll burn the motor. That’s a super common mistake, by the way. We get so many returns of pumps that ran dry for 2 seconds and died, even though they worked when we shipped them. If you’re not sure how to test it safely, hit us up, we’ll walk you through it over the phone, no hassle.

Now, a few do’s and don’ts I’ve learned the hard way. Do: mark the cable and pipe with a piece of tape before you disconnect anything. That way, when you put the new pump in, you know exactly how far down to lower it—too shallow, and it’ll suck air, too deep, and it might hit the bottom of the well. Don’t: reuse old pipe couplings if they’re rusted. We sell replacement couplings super cheap, don’t risk a leak. Do: check the intake screen on the old pump before you toss it. If it’s clogged with gunk, that might’ve been why your pump died in the first place. Don’t: pull the entire pipe out unless you absolutely have to. Most of the time, you only need to pull the pump and 10-15 feet of pipe, so you save yourself the hassle of reassembling all that.

Wait, one last thing: if you’re replacing the pump, when you’re lowering the new one in, make sure it’s level again, just like when you pulled the old one. And don’t forget to tighten that coupling! We’ve had customers call us at 2 a.m. saying their pump’s leaking, and half the time it’s because the coupling wasn’t tightened enough, or Teflon tape wasn’t applied. Pro move: wrap 3 layers of Teflon tape clockwise around the pipe threads before you connect the coupling, that makes it leak-proof.

I know this seems like a lot, but it’s way easier than it sounds when you take it step by step. And if you’re the type who’d rather leave it to the pros, that’s fine too—we work with independent well techs all over the country, but if you wanna DIY, just take it slow, no rush. At the end of the day, the biggest thing is not cutting corners, because this pump’s gonna last you 10+ years if you handle it right.

If you’ve got a pump that’s acting up, or you need a new one, or even just a replacement part, hit us up to chat about what you need. We don’t do pushy sales stuff—we just give honest advice because we care if your well’s working. If you’re not sure what size pump you need, just tell us your well depth and how much water you use, and we’ll hook you up with the right one, no guesswork. Don’t let a stuck pump or a bad installation turn a routine fix into a headache—we’re here to help.

LBWZB Full Automatic Smart Pump References

  1. Water Wells: A Guide to Domestic Water Supply, National Ground Water Association
  2. Submersible Pump Installation and Maintenance Manual, Franklin Electric Co.
  3. Residential Well Pump Troubleshooting Guide, Water Systems Council
  4. OSHA Safety Guidelines for Working Near Well Systems, Occupational Safety and Health Administration

Longbiao Pump Industry Co., Ltd.
We are one of the most professional submersible pump manufacturers and suppliers in China, featured by quality products and low price. Please rest assured to buy discount submersible pump for sale here from our factory. We also accept customized orders.
Address: Unit 101, Building 11, Pan’ao Entrepreneurship Park, Daxi Town, Wenling City, Taizhou City, Zhejiang Province, P.R. China
E-mail: 1653746797@qq.com
WebSite: https://www.cnlongbiao.com/