Hey there, if you’re running a warehouse, manufacturing plant, or logistics hub, you probably already know how frustrating it is when two conveying lines don’t play nice together. I’m Jake, been in the conveying line supply game for 12 years, and I’ve seen it all: mismatched conveyors causing bottlenecks, products falling between gaps, even full shutdowns because someone tried to “rig” a connection with a random piece of metal. Today, I’m breaking down exactly how to connect two conveying lines properly—no jargon, no guesswork, just what actually works for your setup. Conveying Line

First, let’s hit the basics before we get into the step-by-step. Not all conveying lines are the same, right? There’s belt conveyors, roller conveyors, chain conveyors, even flexible screw ones—each needs a different connection fix. I’ve had customers come to me before saying, “I just bolted two lines together and it worked,” until a pallet of heavy parts got stuck and took out a whole section. So first rule: know your line type. If you’re moving small, lightweight items (like retail packaging), a roller line connection is way different than a heavy-duty belt line for automotive components. Got that out the way.
Now, let’s get into the actual process. I’ll walk you through the core steps that work for almost every standard line, plus tweaks for the most common setups.
Step 1: Prep the Ends of Both Lines. This is the part most people skip, and it’s why connections fail fast. You can’t just line up two cut ends and call it good. First, turn off all power (duh—safety first, I don’t care how in a hurry you are, don’t skip this). Then, measure both ends to make sure they’re at the exact same height. If one line is 1/4 inch higher than the other, products will either tip over or get jammed when moving between them. I use a digital level for this—way more accurate than a old bubble level, and it takes 10 seconds.
Next, check the surface of each end. For roller conveyors, make sure the rollers aren’t bent or sticking—if a roller is off, it’ll catch items mid-transfer. For belt conveyors, you need to trim the belt ends straight with a belt cutter, not a pair of scissors. Scissors leave frayed edges, which will break off and get stuck in the line later. For chain conveyors, clean the chain links at the end—any gunk (grease, debris) will make the connection tight and cause wear. I always keep a small wire brush in my toolbox just for this, saves so much time later.
Step 2: Pick the Right Connection Hardware. This is where a lot of suppliers try to upsell you on fancy parts, but most of the time, you don’t need that. It depends on your line type, so let’s break it down:
If you’re connecting roller conveyors (super common in e-commerce warehouses), the go-to is a “roller transition plate.” It’s a flat metal plate that sits between the two lines, with rollers that align perfectly with the end rollers of each line. Wait—don’t just use any plate. Make sure the plate’s rollers are the exact same diameter and spacing as your line’s rollers. If they’re smaller, small items like tiny screws or envelopes will drop through the gap. I’ve had so many customers come back after buying the wrong plate, so always double-check your roller specs before ordering.
For belt conveyors, connecting two lines usually means a “butt splice” or a “lap splice,” but wait—you’re connecting two separate lines, not splicing one belt. Oh right, for line-to-line belt connections, the best thing is a transition belt or a conveyor belt joiner plate. The joiner plate fills the gap between the two belts, so items slide smoothly. If you leave even a 1-inch gap, boxes with weak bottoms will tear open. I’ve seen this happen with medical supply boxes—they’re lightweight but have thin cardboard, so a gap means spilled supplies and lost product.
Chain conveyors (think heavy parts, car engines) are different here. You need a chain connector link, plus a tensioner to make sure the chain doesn’t slip when transferring loads. Heavy loads pull hard, so a flimsy connector link will break. I always recommend using a “master link” for chain conveyors—they’re designed for heavy loads, way more reliable than a standard quick link.
Side note: If you’re connecting a powered line to a non-powered one (like a gravity roller line next to a motorized belt line), you need to add a “snubber roller” or a small guide rail on the sides. Gravity lines let items roll fast, and if the motorized line is moving slower, the product will shoot off the end. That snubber roller slows it down just enough so it transfers smoothly.
Step 3: Align, Secure, and Test. Okay, you’ve got your hardware, your lines are prepped—now line them up. This isn’t just eyeballing it. Use a straight edge (like a long aluminum bar) to run along the top of both lines—if there’s a gap between the bar and the line, you need to adjust the height or angle. Once aligned, bolt the connection hardware to both lines. Don’t over-tighten the bolts—you’ll bend the line frame, which causes more issues. A good rule: tighten until the hardware doesn’t wiggle, and it’s flush with the line’s surface.
Now the test run. Start with a small, light item first—something that’s easy to replace if it gets stuck. Then work up to the heaviest load you normally move. If the item transfers smoothly without getting stuck, tipping, or falling between lines, you’re good. If not, don’t panic—common fixes are adjusting the height, adding a side guide, or checking if the hardware is the right size. I once had a customer test with a small box, it worked, then when they tried a 50-pound pallet, it jammed—turns out the transition plate was too short, so the pallet hung over the gap. Easy fix once you test with your actual loads.
Wait, are there any mistakes I see all the time? Let’s list the big ones so you don’t make them:
-
Ignoring side gaps. A lot of people focus on height and roller alignment, but if the sides of the two lines are even 1/8 inch off, small items can fall off the side mid-transfer. Add side rails to both lines if they don’t have them—cheap insurance.
-
Forgetting to account for product size. If you’re moving items that are 6 inches wide, you don’t need side rails that are 12 inches tall, but you do need to make sure the rails match up perfectly. Too narrow, and items fall out; too wide, and they might tip.
-
Skipping the tension check for powered lines. If one line is motorized, make sure the connection hardware doesn’t pull too tight or too loose. Too tight, and the motor will burn out; too loose, and the hardware will shift. A quick tug test works—if it moves more than 1/4 inch, adjust the bolts.
Now, let’s talk about when you might need a pro, because even if you follow all this, some setups are tricky. If you’re connecting lines that are in different parts of a large warehouse, or handling super fragile items (like glass bottles or electronics), it’s worth hiring a conveyor specialist. We’ve got guys on my team that do custom connections for those cases, because one wrong move can cost you thousands in damaged product or downtime.
Wait, also—if you’re using flexible conveyors (the ones you can bend around corners), connecting two of those is different. You’ll use a flexible connector joint, not a hard plate. Make sure it’s rated for your conveyor’s weight limit. I’ve had customers try to use a regular plate for flexible lines, and the bend caused the plate to break.
At the end of the day, connecting two conveying lines isn’t rocket science, but it’s not just slapping parts together either. The key is prep, matching hardware to your line and products, and testing with actual loads.

If you’re not sure about your specific setup, don’t guess. My team can walk you through exactly what parts you need, even help you measure your lines over the phone—no confusing quotes, just straight-up advice. We’ve supplied conveyors to warehouses, manufacturers, and distribution centers all over, so we know how to get your lines working together without the hassle. Hit us up to talk through your needs, and we’ll make sure you’ve got the right connection to keep your operations moving smoothly.
Conveying Line References
Conveyor Equipment Manufacturers Association (CEMA) Standards for Conveyor Alignment and Transfers, 2022
Industrial Conveyor Association (ICA) Guide to Line Connection Hardware, 2023
OSHA Safety Guidelines for Conveyor System Installation and Maintenance, 2021
Shenzhen Ginnee Intelligent Warehousing Robotics Co., Ltd.
As one of the most professional conveying line suppliers in China, we’re featured by quality products and low price. Please rest assured to wholesale durable conveying line in stock here and get quotation from our factory. We also accept customized orders.
Address: Room101, No.162 JunXin Road, Niuhu Community, Guanlan Strect, Longhua District, Shenzhen, Guangdong Province, China.
E-mail: huangyongmei@szginnee.com
WebSite: https://www.ginneerobotics.com/